ANTI GRAFFITI PRODUCTS

• DISAPPEAR Organic Graffiti/Adhesive Remover™
• DISAPPEAR Organic Graffiti/Adhesive/Paint Remover™
• ND GRAFFITI SHIELD™
• ONE COAT™

GRAFFITI SHIELD SYSTEM™ KIT

ND GRAFFITI SHIELD™

Water Based Sealer & Finish

ND GRAFFITI SHIELD™ is Part 2 of our GRAFFITI SHIELD SYSTEM™, it is anti-graffiti protective coating that will prevent typical damages often seen when attempting to remove graffiti spray paints and marker inks from wall paints, and on all wall materials. It may be installed both inside and outside the property. It eliminates the need to repaint a wall caused by damage to the wall paint by the removal methods used. It eliminates the formation of "shadows" commonly seen on walls after attempted cleanings.ND GRAFFITI SHIELD™ is applied in 4 coats over ONE COAT™ Primer/Sealer/Finish.

ND GRAFFITI SHIELD™ is water based, safe and pleasant to use as directed and is extremely low in odor. It dries water clear and enhances the natural appearance of all materials and underlying paints while preventing paints from fading/oxidizing for many years. It is also resistant to attracting soils and dust. Walls stay cleaner looking much longer. Clean from normal soils with just plain water. New graffiti is removed with our DISAPPEAR Organic Graffiti/Adhesive Remover™. Our protective coatings system do not require stripping and they function as a primer should a color change be desired; then, apply it over the new painted color.

MAIN BENEFITS:

1. Available in Glossy and in Satin/Matte Version
2. Prevents Graffiti Damage to Sealed Surfaces
3. Can be Installed on Almost Any Surface or Object
4. Very Low VOC: Only 16.2 g/l per California VOC Regulations
5. Exceptional Durability and Resistance To Staining
6. Does Not Attract Soils and Dust
7. Water Based: Very Low Odor, Easy Cleanup
8. Warranted For 5 years*

TECHNICAL DATA:

KITS For Porous and Semi-Porous Substrates

KITS For Non Porous Substrates (Murals, Paints, Metals, etc)

ND GRAFFITI SHIELD™ Single product

ND GRAFFITI SHIELD™ APPLICATION DIRECTIONS:

ND GRAFFITI SHIELD SYSTEM™ Directions Are HERE

The substrate must be first primed with ONE COAT™ Water Based Primer/Sealer/Finish in sufficient quantity so that it is visible and can be felt on the surface. After it is dry to the touch apply ND GRAFFITI SHIELD™ by spray (airless sprayer with 0.015 or 0.013 tip at about 300-500 PSI is recommended for most large painted and all porous surfaces; low pressure hand pump sprayer at about 35 PSI could be used on very porous surfaces). The application should be thin and ND GRAFFITI SHIELD™ should appear water clear when applied. THE GRAFFITI SHIELD SYSTEM™ is a total of 4 separate coats of ND GRAFFITI SHIELD™ over the base application of ONE COAT™. Each coat must be dry to the touch before next coat is applied. Drying time may vary between few minutes to an hour depending upon the weather, humidity and ventilation.
    THE GRAFFITI SHIELD SYSTEM™ should be used after 96 hours which is the cure time. You can protect the wall while it is curing by covering it with a drop cloth or securing the area. Should cleaning be necessary before 96 hours, reapply ND GRAFFITI SHIELD™ to the needed areas only. Do not allow this product to freeze and do not use it in freezing temperatures. However, once it is applied and cured, freeze/thaw cycles will have no effect on proper product performance.
    Remove new graffiti from THE GRAFFITI SHIELD SYSTEM™ in 24 hours or less for better results. Use our DISAPPEAR Organic Graffiti/Adhesive Remover™ - apply to area and allow it to soak on graffiti for 5 minutes to about 15 minutes and flush with water, clean with a soft cloth, or powerwash the area. When necessary, touch up cleaned areas with a light coat of ND GRAFFITI SHIELD™.
    Please test this product on a small inconspicuous area before proceeding with the job.

HOW MUCH OF ONE COAT™ and ND GRAFFITI SHIELD™ DO I NEED?

    1. Porous materials such as concrete, brick, blocks, stucco:
    - In most cases you will need to apply 2 separate coats of ONE COAT™ according to our directions. The approximate coverage is about 330 sq.ft. per gallon for two coats.
    - You need to apply 4 separate coats of ND GRAFFITI SHIELD™ according to our directions. The approximate coverage is about 250 sq.ft. per gallon for all 4 coats.
    2. Semi-porous materials such as indoor/outdoor house paint, wood:
    - You need to apply 2 separate coats of ONE COAT™ according to our directions. The approximate coverage is about 660 sq.ft. per gallon for both two coats.
    - You need to apply 4 separate coats of ND GRAFFITI SHIELD™ according to our directions. The approximate coverage is about 500 sq.ft. per gallon for all 4 coats.
    3. Non-porous materials such as metals, plastics, non-porous paint:
    - You need to apply one single coat of ONE COAT™ according to our directions. The approximate coverage for this coat is about 2000 sq.ft. per gallon.
    - You need to apply 4 separate coats of ND GRAFFITI SHIELD™ according to our directions. The approximate coverage is about 500 sq.ft. per gallon for all 4 coats.

    The best method to determine the spread rate for these products on your material is to pre-test them on a small inconspicuous area according to our Directions. Our estimates should not be relied on to be accurate for your application.

QUESTIONS? CONTACT US NOW